How To Fix Pressure Cracks On A Skateboard

Ever seen little cracks near the bolts or edges of your skateboard deck? Yeah, Those are pressure cracks on a skateboard, and they’re super annoying. They usually show up after hard landings or a lot of use. If you ignore them, they can get worse and ruin your skateboard.

Table of Contents

I know you are thinking about how to fix pressure cracks on a skateboard. Don’t worry! In this article, I’ll show you exactly how to repair your deck so you can get back to skating.

It is a simple and easy process. You don’t need special tools, and it won’t take much time.

So, are you ready to dive in? Let’s get your board back in top shape!

What are Skateboard Pressure Cracks on a Skateboard?

Pressure cracks are small lines or splits in your skateboard deck. These happen when your board is stressed—like when you land tricks, overtighten your hardware, or skate in bad weather.

Cracks are most common around the truck bolts or edges of the deck. They can be shallow or deep. Small ones aren’t usually a big deal, but larger ones can damage your board.

Is It Normal for Pressure Cracks on a Skateboard?

Yes, pressure cracks are normal. Skateboarding is rough on your board. Even the best decks will get them eventually.

Not all pressure cracks are serious. Some are only on the surface. But if they grow deeper or spread, you need to fix them or replace the deck.

Are Pressure Cracks Bad on a Skateboard?

Not always. Small cracks usually don’t affect how your skateboard works. But larger ones can weaken the deck and even cause it to break.

If the cracks are spreading, don’t ignore them. Fix them early to keep your board strong.

How To Fix Pressure Cracks On A Skateboard: With Simple Process

In this section, I will show you how to repair your board step by step. Even if you’ve never done it before, you’ll have your skateboard ready to ride again. Let’s get started!

What Do You Need to Fill Pressure Cracks on a Skateboard?

First of all, you’ll need these below:

Epoxy resin (strong and wood-friendly)

Putty knife or old card

Fine sandpaper (200–400 grit)

Clamps (optional)

Clean cloth

So, I think you should grab these tools. Now, let’s dive into the process:

Inspect the Cracks: Look at the cracks closely. Are they small or deep? If they’re small, they’re easy to fix. If they’re large or spreading, you may need to replace the deck.

Clean the Area: Wipe the cracks with a clean cloth to remove dirt and dust. The epoxy will stick better to a clean surface.

Fill the Cracks with Epoxy: Mix the epoxy resin as the package says. Use a putty knife or card to press the epoxy into the cracks. Fill them completely.

Let the Epoxy Dry: Leave the board flat in a dry spot for 24–48 hours. Don’t use the board until the epoxy is fully cured.

Sand the Area: Once the epoxy is dry, sand it with fine sandpaper. This will smooth the surface and make your board feel normal again.

Test Your Board: Reattach the trucks and test the board. If it feels sturdy, the repair worked!

However, if you have big crack on your board, then you should read the article below to fix it!
How to Fix a Cracked Skateboard: 06 Easy Steps For Beginners!

How to Prevent Pressure Cracks on a Skateboard

It’s easier to stop cracks than to fix them. Here’s how to avoid pressure cracks on a skateboard:

Don’t Overtighten Trucks: Tighten your bolts just enough to hold the trucks in place. Over-tightening puts extra stress on the deck.

Use Shock Pads: Shock pads absorb impact and reduce stress on your board. They’re especially helpful for hard landings.

Avoid Bad Weather: Keep your board out of the rain and heat. Moisture and heat weaken the wood.

Land Tricks Properly: Try to land with your weight evenly distributed. This helps avoid putting too much pressure on one spot.

Check Your Board Often: Look for small cracks regularly. Fix them early to stop them from spreading.

Wrapping Up

Pressure cracks are a common problem for skaters, but they’re easy to fix. Using epoxy resin and following simple steps can save your deck and keep you skating.

To avoid cracks, take care of your board. Don’t over-tighten the trucks, use shock pads, and keep them out of bad weather.

If your board feels weak even after a repair, don’t risk it. Get a new deck, and keep shredding safely!